I walked out to the warehouse and pulled the Draw-Tite Custom Fit Vehicle Wiring # 118258. This wiring kit uses a 10 amp fuse in the yellow fuse holder.
I have linked instructions for the Draw-Tite Custom Fit Vehicle Wiring # 118258. view full answer...
If you destroyed one of the plugs at the end of your Curt T-Connector Vehicle Wiring Harness, # C55124, then this wiring harness will need to be replaced. Replacement plugs are not available.
If it is the factory plug that was destroyed you will need to contact your local Jeep dealer for a replacement. view full answer...
According to my contact at TowReady the red fuse supplied in their T-One Vehicle Wiring Harness # 118467 for the 2013 Subaru Outback Wagon is a 10-amp mini fuse commonly available at auto parts stores. view full answer...
It looks like you are looking for a replacement trailer connector for your 1999 Ford F150 pickup truck.
The Tow Ready Replacement 7-Way Wiring Harness, part # 118242 is an exact replacement for the OEM harness.
To install the harness you will need to locate the vehicle’s wiring harness plugs located in the rear, underneath the vehicle, inside the driver’s side frame rail. The plugs should match the trailer wiring harness ends. Just disconnect the vehicle wiring harness and install the... view full answer...
The reason the Curt Custom Fit Vehicle Wiring # C56310 has a power wire is to protect the delicate tail light wiring circuits of your vehicle from being overloaded. The Curt Trailer Harness # C56310 that you referenced uses your tail light circuits as signal wires and then draws the power to illuminate the tail lights of your trailer directly from your vehicle battery through the battery wire of the box. Not doing this will void the warranty of the kit.
I attached installation instructions... view full answer...
For a 4-way trailer wiring kit confirmed as a fit for your 2015 Honda Pilot we have the Tekonsha kit part # 118558 which would be exactly what you need. This is a custom install kit that plugs into your vehicle's exsiting wiring to provide you with a 4-way. view full answer...
In order to have a 12V power supply at the vehicle connection point for a trailer you will need to have a fully functioning 7-way.
For your truck I recommend using the Tow-Ready Custom Fit Vehicle Wiring Harness # 118243. This harness will replace your existing 4-way, and upgrades it to a 7-way connection using the factor plug. The fuses and relays are included that will be used in your power distribution box, and the trailer towing relay block.
Once you have a functioning 7-way installed... view full answer...
I am sure that the # HM40975 will work as a replacement 7-way for your 2006 Land Rover LR3, but I am not totally sure it would fit into the mounting hole you have on your vehicle. There is a chance it would, but worst case scenario you would have to use the included bracket to install the 7-way to the bumper of the vehicle.
Feel free to send me a picture of the mounting location on your vehicle though. view full answer...
The Replacement Multi-Tow 7-Way & 4 Pole Trailer Connector, # 74682, was designed to replace the factory 7-way on your 2009 Toyota Tacoma. Just unplug the connector from the back of your current 7-way and plug it into the back of the replacement connector. view full answer...
You can use the Pollack 7-Pole Trailer Socket, # PK12-707E, on your 2001 Dodge Dakota quad cab. Keep in mind, this is not an OEM replacement socket, so the wires will need to be attached to each terminal in the socket. I have attached a photo showing how this socket should be wired. It is important that you wire the socket by function and not wire color since vehicle manufacturers are not known to follow an industry standard color code.
If you are replacing an OEM 7-way, then you may... view full answer...
The two parts you will need to replace your damaged 7-way on your 2000 Ford F-250 and add a 4-flat connector to the rear of your vehicle is the Tow Ready Custom Fit Vehicle Wiring for the 2000 Ford F 250 and F 350 Super Duty, # 118243, and the Hopkins Pollak 7- and 4-Pole Trailer Connector Socket w/ Mounting Bracket - Vehicle End, # HM40975.
The Tow Ready harness # 118243 is an exact replacement for the damaged OEM Wiring Harness and connects directly to the Standard OEM Connector. It... view full answer...
To replace the hardware for your Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" # C13167 for your 2020 Ford Transit Connect you'll need to order part # RHK and then select Curt as the manufacturer and input 13167 for the hitch number. This will get you any hardware that would have come with the hitch when you first installed it on your 2016 Transit Connect, including the guide wire you mentioned.
Attached is an installation video of this hitch on a 2020 Transit Connect for you... view full answer...
You need the Replacement Hardware Kit for Trailer Hitches Item # RHK to install the Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2" Item # 76034 on your 2014 Ford Explorer. As far as a wiring I recommend the Curt T-Connector Vehicle Wiring Harness with 7-Way Trailer Connector Item # C56278. This harness plugs directly into factory plugs, located under the vehicle, on the passenger side. I recommend using Dielectric Grease for Electrical Connectors, 2 oz. Item #... view full answer...
I can understand not wanting to undo the wiring and then re-do it, and the pigtail harness is available separately for the Tekonsha Prodigy P3 # 90195. The correct part is the following:
- Replacement Brake Control Plug-In Harness # 20127
One end of this will plug into the P3 and the other end will hardwire to your new vehicle. In case you were interested in a new mounting bracket as well, the correct part for that is the Replacement Mounting Bracket Kit for Tekonsha Prodigy P3 Trailer... view full answer...
We do have the replacement hardware for the Draw-Tite # 76020.
You will need Replacement Hardware Kit For Trailer Hitches # RHK and enter the hitch item number 76020, and Select Draw-Tite from the drop down menu. This will include the fish wire and everything needed to complete the install. view full answer...
For your Aries ActionTrac Motorized Running Boards with Custom Installation Kit # AA3047960, you can use the:
-Custom Mounting Kit for Aries ActionTrac Motorized Running Boards # AA3025160.
This kit includes 6 mounting brackets, 2 LEDs, 1 split wiring harness and is a confirmed fit for your 2017 Nissan Titan XD. view full answer...
For your Roadmaster BlackHawk 2 All Terrain, Non-Binding Tow Bar - Motorhome Mount - 2" Hitch - 10K # RM-422 the fact that they are bound up obviously shows and issue. My recommendation for you is to completely remove the inner bar and replace it with the Replacement Inner Arm for Roadmaster BlackHawk 2 All Terrain and Falcon All-Terrain Tow Bar # 910021-65 on each side. This may require a pipe wrench and some penetrating oil to remove the old bars, but since you are replacing them you... view full answer...
For a 7-way adapter designed for German vehicles towing LED lighted trailer to prevent the bulb out error message we have the part # C57003.
For an adapter that plugs into a 7-way and then provides a 4-way we have the part # C35FR. view full answer...
Blue Ox does make incredibly nice flat towing setups. Their base plates are high quality and their tow bars like the Avail part # BX7420 are basically the nicest ones around. I would highly recommend going that route.
For a base plate kit you will need the part # BX1134 which is a custom fit for your 2017 Jeep Wrangler Unlimited HardRock Rubicon edition. The tabs of this kit can also be removed when not in use which is nice.
In addition to the base plates, you will also need a compatible... view full answer...
We offer beam axles rated for 3500-lbs as well as axle-less suspension systems from Timbren such as their # ASR3500S05. The advantages of these Timbren systems include a lower trailer deck height and increased ground clearance. The bolt or weld right to your trailer's frame
On this kit you can install hub/drums # AKHD-655-35-EZ-K which have the 6-on-5-1/2 bolt pattern and with them use self-adjusting electric drum brakes # AKEBRK-35L-SA (left) and # AKEBRK-35R-SA (right). Use 10-gauge... view full answer...
Go To Results